Before shopping
Before shopping
for a neon dimmer, please determine what type of
neon transformer you have...
neon dimmer, neon sign dimmer, neon dimmers, neon sign dimmers, plug in neon dimmer, plug in neon dimmers, plug-in neon dimmer, plug-in neon dimmers, diversified comonents.
"WALL SWITCH"
NEON DIMMERS
This type neon transformer is also known as a "Core & Coil".  Conventional neon transformers have been around since day one lighting neon.
Heavy @ 10+ lbs.
This type neon transformer is relatively new technology, powering neon for approximately the last 15-20 years. Most new Beer advertising neon signs come with Electronic type neon transformers.
Light @ 1-2 lbs.
All Prices and Specifications are subject to change without notice.
Copyright West Coast Custom Designs, LLC.
c
No reproduction in whole or part without express written permission. All Rights Reserved.
5.2 Amp "IN-WALL MOUNT"
Neon Dimmer  
* In-Wall mount neon dimmer.
* Easy dial allows high/low light intensity control
  as well as on/off function.
* Field Adjustable Trim (this is a low-end
  brightness adjustment. The low-end brightness
  is factory set. If not satisfactory, it may be
  trimmed/changed via an adjustment screw hidden 
  behind the knob).
* Compatible with all brands of Core & Coil/Magnetic
  transformers. For electronics, please see notes
  below.

SPEC'S
* 5.2 Amps Maximum load.
* Input 120vt/60hz - 500VA - 5.2 Amps
* Can handle "1" 15,000vt transformer or smaller.
* For core & coil and electronic type transformers.
* Mounts into a single gang electrical box.
* Trim plate not included.
* Ivory colored knob.
* Lightweight & dependable solid-state construction.
* 4" H x 1 3/4" W x 1 1/2" D (not including knob)
* Made in the USA.
* Diversified Components NE-5
* Six Month Limited Warranty.
Trim Plate Not Included
Side View
Rear View
Rear View
Side View
Installed in Wall View
Installed in Wall View
Installed in Wall View
Side View
Rear View
8.3 Amps "IN-WALL MOUNT"
Neon Dimmer  
* In-Wall mount neon dimmer.
* Easy dial allows high/low light intensity control
  as well as on/off function.
* Field Adjustable Trim (this is a low-end
  brightness adjustment. The low-end brightness
  is factory set. If not satisfactory, it may be
  trimmed/changed via an adjustment screw hidden 
  behind the knob).
* Compatible with all brands of Core & Coil/Magnetic
  transformers. For electronics, please see notes
  below.

SPEC'S
* 8.3 Amps Maximum load.
* Input 120vt/60hz - 1,000VA  - 8.3 Amps
* Can handle "2" 15,000vt transformers or smaller.
* For core & coil and electronic type transformers.
* Mounts into a single gang electrical box.
* Lightweight & dependable solid-state construction.
* 4 1/2" H x 2 3/4" W x 2" D (not including knob)
* Made in the USA.
* UL Listed.
* Diversified Components NE-10.
* Six Month Limited Warranty.

NOTES & LIMITATIONS
* One dimmer can dim several transformers however
  the total Amps of all the transformers combined
  cannot exceed the Amp rating of the dimmer.

* Do not use this dimmer with a high power factor
  transformer.

* GTO lengths between transformer/s and elctrodes
  should be added to tubing footage when
  determining transformer loading to insure adaquate 
  dimming range.

* Care should be taken to avoid underloading
  transformer/s as dimmer may not be effective in 
  dimming tubes with transformers which are rated 
  at 4,000vts or less. In addition, transformers rated
  at 5,000vts/20mA may also not be effective in 
  dimming. Transformers rated at 5,000vts/30mA or
  higher should opperate as intended.

* When using on electronic type transformers, at
  some point of turning the knob brightness down,
  the neon will blink and flash. You will only be
  able to dim down the brightness to right before it
  starts to blink and flash. You might get 70%
  dimming, as little as 10% dimming or anywhere
  in between. Transformer brands react differently
  with the dimmer because there is no industry
  standard for manufacturing them. Each brand uses
  a different fequency to light the neon. It is these
  frequencies that react differntly with the dimmer.

PRICING 

1 - 5  $219.95 ea.

6 - 11  $215.95 ea.

12+  $209.95 ea.
NEW!
NEW!
NEW!
NOTES & LIMITATIONS
* One dimmer can dim several transformers however
  the total Amps of all the transformers combined
  cannot exceed the Amp rating of the dimmer.

* Do not use this dimmer with a high power factor
  transformer.

* GTO lengths between transformer/s and elctrodes
  should be added to tubing footage when
  determining transformer loading to insure adaquate 
  dimming range.

* Care should be taken to avoid underloading
  transformer/s as dimmer may not be effective in 
  dimming tubes with transformers which are rated 
  at 4,000vts or less. In addition, transformers rated
  at 5,000vts/20mA may also not be effective in 
  dimming. Transformers rated at 5,000vts/30mA or
  higher should opperate as intended.

* When using on electronic type transformers, at
  some point of turning the knob brightness down,
  the neon will blink and flash. You will only be
  able to dim down the brightness to right before it
  starts to blink and flash. You might get 70%
  dimming, as little as 10% dimming or anywhere
  in between. Transformer brands react differently
  with the dimmer because there is no industry
  standard for manufacturing them. Each brand uses
  a different fequency to light the neon. It is these
  frequencies that react differntly with the dimmer.

PRICING   

1 - 5  $119.95 ea.

6 - 11  $117.95 ea.

12+  $114.95 ea.
12.5 Amps "IN-WALL MOUNT"
Neon Dimmer  
* In-Wall mount neon dimmer.
* Easy dial allows high/low light intensity control
  as well as on/off function.
* Field Adjustable Trim (this is a low-end
  brightness adjustment. The low-end brightness
  is factory set. If not satisfactory, it may be
  trimmed/changed via an adjustment screw hidden 
  behind the knob).
* Compatible with all brands of Core & Coil/Magnetic
  transformers. For electronics, please see notes
  below.

SPEC'S
* 12.5 Amps Maximum load.
* Input 120vt/60hz - 1,500VA  - 12.5 Amps
* Can handle "3" 15,000vt transformers or smaller.
* For core & coil and electronic type transformers.
* Mounts into a double gang electrical box.
* Lightweight & dependable solid-state construction.
* 4 1/2" H x 4 1/2" W x 2" D (not including knob)
* Made in the USA.
* UL Listed.
* Diversified Components NE-15.
* Six Month Limited Warranty.

NOTES & LIMITATIONS
* One dimmer can dim several transformers however
  the total Amps of all the transformers combined
  cannot exceed the Amp rating of the dimmer.

* Do not use this dimmer with a high power factor
  transformer.

* GTO lengths between transformer/s and elctrodes
  should be added to tubing footage when
  determining transformer loading to insure adaquate 
  dimming range.

* Care should be taken to avoid underloading
  transformer/s as dimmer may not be effective in 
  dimming tubes with transformers which are rated 
  at 4,000vts or less. In addition, transformers rated
  at 5,000vts/20mA may also not be effective in 
  dimming. Transformers rated at 5,000vts/30mA or
  higher should opperate as intended.

* When using on electronic type transformers, at
  some point of turning the knob brightness down,
  the neon will blink and flash. You will only be
  able to dim down the brightness to right before it
  starts to blink and flash. You might get 70%
  dimming, as little as 10% dimming or anywhere
  in between. Transformer brands react differently
  with the dimmer because there is no industry
  standard for manufacturing them. Each brand uses
  a different fequency to light the neon. It is these
  frequencies that react differntly with the dimmer.

PRICING       

1 - 5  $244.95 ea.

6 - 11  $242.95 ea.

12+  $239.95 ea.








Compatible
with all brands of
Core & Coil/Magnetic
transformers - both UL2161 and Non-UL2161 Fault
models.
Compatible
with all brands of
Core & Coil/Magnetic
transformers - both UL2161 and Non-UL2161 Fault
models.
Compatible
with all brands of
Core & Coil/Magnetic
transformers - both UL2161 and Non-UL2161 Fault
models.
E-DIMMER
E-DIMMER
Input: 120vt/60hz - 1.2 Amps.
Output: 10,000vt - 35mA

* Self Adjusting to neon load from 2,000vts - 10,000vts
* Absolutely NO mercury migration.
* Auto Shutdown & Overload Protection.
* Yes... CAN be mounted directly to metal surfaces.
* 9 1/2" length, 2 1/2" wide, 1 3/4" thick.
* Less than 1% failure rate!
* Easy side dial to select brightness.
* Warranty; Limited One Year
* Imported.
Footage Chart
NEON
ARGON
15mm  12mm  10mm   15mm  12mm  10mm
35'       28'        23'          42'       33'       27'
Adjustment
Knob
Another Option... Transformer with built-In dimmer!
>>>Great for Beer Neon Signs<<<
40-100% Dimming
STOCKED
STOCKED
AVAILABLE
NOW!
STOCKED
STOCKED
AVAILABLE
NOW!
STOCKED
STOCKED
AVAILABLE
NOW!
NeonPartsUSA@gmail.com
______________________________________
480-820-9517