NeonPartsUSA@gmail.com
______________________________________
480-820-9517
"UL Listed"
PK type Glass Housing
Wiring System
Overall Wiring Scheme
Close-up #1
Close-up #2
Contact us to order any of the parts.
All Prices and Specifications are subject to change without notice.
Copyright West Coast Custom Designs, LLC.
c
No reproduction in whole or part without express written permission. All Rights Reserved.
PK-type Housing
Step By Step Wiring Instructions
1. Install PK-type Glass Housing or use existing PK
installation.
2. No need to modify the glass insert, simply remove Spring
Assembly.
3. Slide the UL Listed wet-location Neon Electrode
Housing Cap onto the neon tube.
Housing from the back side.
5. Slide the UL Listed wet-location One-Piece Neon
6. Connect the GTO neon wire to the neon electrode.
7. Slide the UL Listed wet-location One-Piece Neon
Electrode Boot onto the neon electrode.
8. Insert connected neon tube into the PK type Glass Housing.
the face of the PK type Glass Housing and snap into
place.This creates a UL Listed wet-location connection.
10. Secure the neon tube to the tube supports.
Existing Glass Insert
Wall Backside View
GTO Neon Wire
11. Backside view of the installation thus far.
12. Install the metal flange.
Installed View
Installing View
Note that the end of the One-Piece Electrode Boot sticks out the bottom of the Metal Flange.
13. Install Sleeving.
that sticks out the bottom of the Metal Flange, making a UL Listed wet location connection.
14. Install 1/2" Flex Conduit.
Installing View
Installing View
Installed
View
Installed View
15. Install High Voltage Splice Box.
16. At the High Voltage Splice Box, bring the flex conduit
a knockout.
17. Inside the High Voltage Splice Box, cut and strip the GTO cable and install on terminal. Finally, secure cover to splice box.
IMPORTANT: The Green Ground Wire on the High Voltage Splice Box must be grounded back to the Main Service Panel using #14 green wire.
Knockout
1. Remove the existing neon tube. Discard the GTO cable and internal PK electrode spring. Verify the neon unit is good.
2. Install Masters Technology's Housing Cap part #MT-GHC200 or #MT-GHC303. Ref: NEC 600:(42):(G).
3. Install Masters Technology's One Peice Neon Electrode Insulator Boot #MT-1PB. Available in 10mm, 12mm, 13mm and 15mm sizes.
4. Use Masters Technology's GTO Sleeving.
5. The PK "glass insulator housing" may be reused or replaced if necessary. Ref: NEC 600:(42):(H):(1):(2).
6. Use 1/2" metal conduit for connection of PK Housing to Splice Box. Ref: NEC 600:(7):(1):(4) - NEC 600(32):(A):(B).
7. GTO Cable. Ref: NEC 600:32):(B):(K)-600:(33):(B):(2).
8. Splice Box. Ref: NEC 600:(32):A):(2):(3)-600:(32):(K).
9. Assemble components as per drawings and directions.
10. Pull on GTO Cable (lightly) to snug assembly. Cut and strip sleeved GTO Cable. Install ontyo terminal post provided in the Splice Box.
11. IMPORTANT: Ground the green wire (located on the Splice Box) back to the main service Breaker Panel. Ref: NEC 600:(5):(B):(1)-600:(5):(C):(1):(2).
12. Equipment grounding conductor shall be Green #14 copper wire. Ref: NEC 600:(7):(1):(2).
PARTS
MT-1PB
Material: #3000 Polymeric Blend
UL Listed: Yes
Made in the USA
Count: 150-Count
Color/s:
Sizes: 10mm 12mm 13mm 15mm
BLACK
WHITE
GRAY
1+ Bags.....
5+ Bags.....
10+ Bags.....
25+ Bags.....
$183.95 ea.
n/a
n/a
n/a
COST
Individual 10-Pack - "Black Only" $48.90 ea.
1+ Bags.....
5+ Bags.....
10+ Bags.....
25+ Bags.....
$219.95 ea.
n/a
n/a
n/a
COST
Individual 10-Pack - "Black Only" $46.90 ea.
1+ Bags.....
5+ Bags.....
10+ Bags.....
25+ Bags.....
$204.95 ea.
n/a
n/a
n/a
10mm
12mm
13mm
One-Piece Cap
COST
Individual 10-Pack - "Black Only" $52.40 ea.
1+ Bags.....
5+ Bags.....
10+ Bags.....
25+ Bags.....
$243.95 ea.
n/a
n/a
n/a
15mm
This "best on the market" system combines GTO cable sleeving, neon electrode insulator boots and other components to create a
"UL Listed - Wet Locations" product.
Manufactured from the highest quality materials including the proprietary #3000 Polymeric Blend. This blend was developed through extensive research, testing, and field evaluations. These provide dependability, good flexibility low and high temperatures, the highest flammability rating 945V, 17000 VT, dielectric withstand, and excellent weathering properties.
This system of products have been awarded patents in the USA and Canada and have both UL and CSA Listings. Their unique design facilitate installation, increase product safety, reduce lighting failures as well as lowering customer service call-backs.
COST
Individual 10-Pack - "Black Only" $43.90 ea.
All prices subject to change without notice.